VENLAC WALL PUTTY
Great Binding Solution For Interior And Exterior Surfaces
Good Water Resistance
Provides Smooth and Uniform Finish to Rough Plasters
Controlled Water Vapour Permeability
Fills Hair Cracks and Pinholes
Excellent Abrasion Resistance
Resists Growth of Algae and Fungi on Wall

Product Description
Venlac Wall Putty is a combination of high quality white portland cement, natural minerals & special additives. It is specially manufactured to impart toughness, durability, binding, waterproofing and longer life to exterior and interior surfaces. Venlac Wall Putty hides the minor imperfections of the surfaces and prevents hair line cracks to appear on the surface.

PLASTER
New masonry surfaces must be allowed to cure completely. Recommended curing time is 28 days as the curing time for new masonry surfaces.
CLEANING
Ensure the surface is completely free from all dirt, loosely held plaster, powdery residue, oil grease or any other contamination. Any previous growth of fungus, algae or moss needs to be removed thoroughly by vigorous wire brushing and cleaning with water.
FILLING THE CRACKS, HOLES & DENTS
For filling cracks upto 3mm, holes and dents use white cement and fine sand in the ratio 1:3
For interior surfaces or substrates that are subjected to continuous seepage or dampness, kindly get the repairs done before the top coat application.

PAINT APPLICATION PROCESS
APPLICATION | RECOATING PERIOD |
---|---|
STEP 1: SANDING | Sand the surface with emery paper 180 and wipe clean |
STEP 2: APPLICATION OF PRIMER BRUSH \ ROLLER \ SPRAY | Apply a coat of SNOWCEM EXTERIOR / INTERIOR PRIMER as per application requirements. |
STEP 3: SNOWCARE WALL PUTTY TROWEL \ PUTTY KNIFE | 06 to 08 Hours. Depending upon climatic Condition. |
STEP 4: SNOWCARE WALL PUTTY TROWEL \ PUTTY KNIFE | 06 to 08 Hours. Depending upon climatic Condition. Sand the surface with emery paper 320 & wipe clean. |
STEP 5: APPLICATION OF PRIMER AND EMULSION COATE BRUSH \ ROLLER \ SPRAY | Apply a coat of PRIMER followed by 2-3 coats of emulsion paint. |
- Recoat period is quoted for 25oC and 50% Relative Humidity, these may vary under different conditions.
- Some shades may require 3 coats for proper hiding.
APPLICATION OF PRIMER IS MANDATORY

Nature | White in Powder Form |
---|---|
Base | White Portland cement and natural minerals |
Colour | White |
Finish | Smooth Finish |
Mode of Application | Trowel, Putty knife/blade |
Drying Time | 4 hours under normal climatic conditions |
Recoating period | 6 to 8 Hours |
Potlife | To be used within 1 hour after mixing |

Handling & Storage
Keep containers airtight during handling and storage to avoid loss of material. Store Venlac Wall Putty in a cool dry place and also protect it from extreme climatic conditions during storage, in transit and at site.

Safety Measures
Kindly refer to the MSDS for Venlac Wall Putty which gives detailed information on safety measures while handling the paint, which is available on request.
Store the container with the lid tightly closed in an upright position, in a cool, dry place.
Keep out of reach of children and away from eatables.
May be harmful if swallowed. In case of ingestion seek immediate medical attention. In case of skin contact immediately wash skin with soap and plenty of water. Get medical attention if irritation develops or persists.
Wear eye protection during application. In case of contact with eyes, rinse immediately with plenty of water and seek medical advice. Do not breathe vapour or spray. It is recommended to wear suitable nose pad during sanding and surface preparation to avoid dust inhalation.
Do not pour leftover paint down the drain or in water courses.
In the event of spills, contain spillage using sand or earth.

